Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in St. Paul?
A chimney liner replacement in St. Paul typically runs $2,600 to $5,800 for a standard masonry flue serving a wood-burning fireplace, and a partial chimney rebuild usually costs $4,500 to $12,000 depending on how much brickwork has to come down. A full liner plus rebuild on a badly deteriorated chimney can reach $14,000 or more. Those ranges reflect what the work actually takes here: a 1920s brick chimney on a Summit Hill or Cathedral Hill house, sized for a coal-era appliance and now heating with gas or wood, is a very different job than a straight stainless drop-in.
We’ll walk through what drives each line item, where the money goes, and how to tell when resurfacing beats a full reline.
Chimney Liner & Rebuild Cost Breakdown (2026)
Here’s what the major pieces of work cost in the St. Paul market this year. These are typical installed ranges, not quotes. The written estimate sets the final price.
| Work Item | Typical Cost Range | What It Covers |
|---|---|---|
| Stainless flexible liner, standard masonry flue | $2,600 – $4,400 | Liners, top plate, cap, insulation wrap, appliance connection |
| Stainless liner with insulation and offset/ovalized fit | $3,600 – $5,800 | Ovalized or offset flue, wrapped insulation, custom terminations |
| HeatShield flue resurfacing | $1,800 – $3,400 | Cleaning, joint repair, ceramic resurfacing of a sound masonry flue |
| Chimney crown rebuild or replacement | $650 – $1,600 | Removing failed crown, forming and pouring a new crown, curing |
| Partial chimney rebuild (above roofline) | $4,500 – $9,000 | Tear-down to sound courses, new brick and mortar, flashing, crown |
| Full chimney rebuild with liner | $9,500 – $14,000+ | Rebuild plus new liner system sized for the appliance |
| Cap and flashing replacement | $350 – $1,200 | Custom or multi-flue cap, new step and counter flashing |
| Inspections (Level 1 / Level 2) | $150 – $450 | Visual or camera inspection, written report |
The swing between the low and high end of each line has a lot to do with the flue itself. A clay tile flue with clean, straight walls takes a factory-insulated liner quickly. A flue that’s been relined once before, has broken tiles, or is offset mid-run takes more labor and often a custom ovalized fit. Masonry rebuilds move the number in bigger jumps because they combine three trades: tear-down, brickwork, and the liner that goes back in afterward. Everything above sits on a foundation of correct diagnosis, which is why the inspection comes before the number, not after.
The 2026 St. Paul Pricing Reality
Two things push costs up in this market compared with what homeowners find quoted on national sites. First, the housing stock. Large parts of St. Paul – the West Seventh neighborhood, Frogtown, Dayton’s Bluff, the blocks around Macalester-Groveland – were built between roughly 1890 and 1930, when chimneys were sized and built for coal. Original brick laid a hundred-plus years ago, in a climate with hard freezes and thaws every winter, holds up better than people expect but eventually spalls. When it does, the repair isn’t cosmetic. Second, access. A chimney on a low-pitched roof is a straightforward setup. A chimney tucked behind a dormer on a steep Victorian roof takes staging and time, and that shows up in the estimate.
We specify every liner for cold-weather performance because a St. Paul heating season is long. A liner that would be fine in a mild climate gets specified differently here. That’s not an upsell – it’s a materials decision. DuraFlex flexible liner systems are what we use for demanding relines because they hold up under prolonged heating-season demand and are built to make the tight transitions older masonry flues require. HeatShield is what we reach for when the flue is sound but the surface isn’t: it resurfaced rather than replaced, which saves real money when the underlying structure is still good.
What Affects Chimney Liner & Rebuild Pricing in St. Paul
Six factors move the number the most on this kind of work. Each one is worth raising before the estimate, not after.
- Flue size and shape. A straight 8×8 clay flue is the easiest case. A larger masonry flue – common on houses built for coal and later converted – may need an oversized liner, a custom ovalized fit, or both. This is exactly the kind of job many sweep-only companies decline. It’s also where the price gap between a standard reline and a technically demanding one shows up.
- Condition of the existing clay tile. Sound tile with intact joints can sometimes be resurfaced with HeatShield instead of fully relined. Cracked, spalled, or missing tile means a full liner. The difference between these two paths is where most of the cost variance sits, and it’s why we do a camera inspection before quoting either way.
- How much brickwork needs to come down. Rebuilds are priced by the course. A chimney with a failed crown and a few spalled courses above the roofline is a partial rebuild. A chimney with deteriorated brick below the roofline, damaged flashing, or a failed interior structure can mean opening up the chase. The range is wide because the work is genuinely different in each case.
- St. Paul’s freeze-thaw cycle. Our winters and the freeze-thaw cycling that comes with them are hard on mortar joints and brick faces. Chimneys on the north side of a house, shaded from sun and slow to dry, weather faster here than on a south-facing wall. That reality shows up in what we specify: a rebuilt chimney here needs detailing that drains water away from the masonry, or it will spall again within a few seasons.
- Appliance type and conversion. A wood-burning fireplace, a gas insert, and an oil-to-gas conversion each need a differently sized liner. Conversions are the ones most often mishandled by generalists: the old flue is the wrong size for the new appliance, and the liner has to make up the difference. Getting that wrong affects draft and safety, not just efficiency.
- Termination and cap. A properly fitted cap and flashing prevent water infiltration and animal intrusion – two of the most common causes of chimney deterioration we see. Famco and Gelco cap and flashing solutions are what we specify. A custom multi-flue cap costs more than a single-flue stock cap, but replacing one because it fits badly later costs more still.
When Resurfacing Costs Less Than Relining
This is the single biggest cost lever on the page. HeatShield flue resurfacing can often put a sound-but-deteriorated clay flue back into service without full demolition or a full liner removal. If the existing flue is structurally intact and the problem is the interior surface – joint gaps, cracked liner faces, spalling – resurfacing can save a homeowner a meaningful amount compared with a complete reline.
We’ve seen too many chimneys relined that just needed resurfacing, and a few that were resurfaced that should have been relined. The only honest way to know which one yours is, is to look at it with a camera and document what’s found. That’s what a Level 2 inspection does, and it’s worth the $150 to $450 before committing to a $4,000 decision.
How to Save on Chimney Liner & Rebuild
Savings come from doing the right work at the right time. We’re not going to pretend a rebuild is something you can defer forever, but there are real ways to keep the number down without cutting into the quality of the work.
- Get an inspection before the rebuild is a rebuild. A crown or flashing problem caught early is a $650 to $1,600 repair. Caught late, it’s water damage into the masonry and a rebuild at $9,500 or more. The inspection pays for itself many times over in that scenario.
- Ask about resurfacing before relining. If the flue is structurally sound, HeatShield resurfacing can save a significant amount compared with a full liner. We’ll tell you when the numbers favor each path.
- Keep water off the chimney. A correctly fitted cap and intact crown are the cheapest insurance a chimney has. We use Famco and Gelco cap and flashing solutions because a properly fitted termination solves the problem rather than being a stopgap.
- Get a written estimate before the work starts. Estimates are free, and the price is set per job by the written estimate. That means no surprise line items once the chimney is opened up – the number on the estimate is the number on the invoice, unless you approve a change.
- Do a full inspection, sweep, and repair under one roof. Coordinating separate contractors for inspection, repair, and relining adds cost and confusion. We do all three. After we repair a chimney, we inspect it and document the result in writing.
- Tell us the appliance. Knowing whether the flue serves a wood fireplace, gas insert, or oil-to-gas conversion helps us quote accurately the first time. Conversions are the most technically demanding relines we handle, and they’re worth flagging up front.
We use professional-grade materials for a reason: they hold up. A cheaper liner that fails early is the opposite of savings. Our technicians have up to 11 years of experience, and they understand that a chimney specified for a St. Paul winter is a different thing than one specified for a mild climate. That’s the standard every job is held to here.
Can you fix a chimney liner or rebuild the same day?
Liner installations and rebuilds are rarely same-day jobs. A full rebuild runs several days, and a liner installation requires inspection, sizing, and curing. Same-day service applies to inspections and sweeps, not structural repairs. Call (866) 942-6061 for an exact quote – estimates are free. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
FAQs – Chimney Liner & Rebuild Cost
How much does chimney liner replacement cost in St. Paul?
A chimney liner replacement in St. Paul typically costs $2,600 to $5,800, with the higher end applying to ovalized offsets, conversions, and added insulation. The written estimate sets the final price. Call (866) 942-6061 – estimates are free.
How much does a chimney rebuild cost in St. Paul?
A partial chimney rebuild above the roofline typically costs $4,500 to $9,000, and a full rebuild with a new liner runs $9,500 to $14,000 or more. The range depends on how many courses come down and whether the interior needs relining. Call (866) 942-6061 for a written estimate.
Is HeatShield resurfacing cheaper than a full reline?
Yes, HeatShield resurfacing typically costs $1,800 to $3,400 and can save a homeowner several thousand dollars compared with a full reline when the flue is structurally sound. It’s not always the right answer – cracked or missing tile calls for a full liner. An inspection determines which path yours needs. Call (866) 942-6061 to schedule one.
How much does chimney crown repair cost in St. Paul?
A chimney crown rebuild or replacement typically costs $650 to $1,600, depending on the chimney’s size and access. Doing it before winter cracking progresses into a full rebuild is the cheapest money a homeowner can spend on a chimney. Call (866) 942-6061 – estimates are free.
Do I need an inspection before a quote?
Yes. A Level 2 inspection typically costs $150 to $450 and gives you the camera-based assessment any liner or rebuild quote should be based on. It’s the only way to know whether resurfacing or relining is the right path, and it’s documented in writing. Call (866) 942-6061 to book one.
If your chimney is on the older side – and in this city, most are – it’s worth knowing what’s actually there before committing to a repair budget. We work across St. Paul and offer a full sweep, repair, and inspection so you don’t have to coordinate a separate inspector after the work is done. Reach out to Tundra Chimney Sweep for a written estimate before you spend anything.
Every job starts with the same question: what does the flue actually need, and what’s the most cost-effective way to get it there? That’s what we answer on the estimate. For a free estimate on liner, rebuild, or resurfacing work in St. Paul, call (866) 942-6061. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the St. Paul market as of 2026. Tundra Chimney Sweep offers free estimates – call (866) 942-6061.
Written by the team at Tundra Chimney Sweep.
What Our Customers Say
"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Scott Parker"Showed up when they said they would. That's most of the battle."
- Allen Chen"Good work. The written inspection report took about a week to arrive after I asked for it, which was slower than I expected."
- Doug Miller