Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in St. Paul?
Chimney repair in St. Paul typically runs $150 to $1,400 for most single-issue jobs, with a simple crown repair at the low end and a partial masonry rebuild at the high end. A full flue reline usually lands between $1,800 and $4,500 depending on liner length and material. The written estimate you get after an inspection sets the final price, and it’s free to find out where your chimney actually sits.
St. Paul winters put a chimney system through a punishing cycle: months of steady burn, then a spring thaw that works water into every crack and joint. That freeze-thaw rhythm is why repairs here so often start as a small crown crack and end as a rebuilt flue. Getting a real range in front of you before anyone climbs the roof is the whole point of this guide. Here’s what things tend to cost across the city, and why one job in Highland Park can price differently from the same job in Frogtown.
Key Takeaways
- Most single-issue chimney repairs in St. Paul fall between $150 and $1,400.
- Partial masonry rebuilds run $1,400 to $4,000; full relines run $1,800 to $4,500.
- HeatShield flue resurfacing often costs less than a full reline when the flue is a candidate.
- Cap and flashing work is the cheapest way to prevent the water damage that drives big bills.
- Estimates are free, and the written estimate sets the price.
Chimney Repair Cost Breakdown (2026)
The table below shows typical estimated ranges for the repairs we price most often in St. Paul. Every chimney is different, and a technician needs to see the flue, crown, flashing and cap before anyone can quote a real number. These ranges are for a typical single-family home; treat them as a starting point, not a bid.
| Repair | Typical Estimated Range | What Drives the Price |
|---|---|---|
| Cap replacement (Famco or Gelco) | $150 – $500 | Single-flue vs multi-flue, custom sizing, animal-guard screens |
| Crown repair | $200 – $700 | Patch vs full crown rebuild, crack depth, access |
| Chimney flashing repair | $250 – $850 | Roof pitch, whether step flashing is rebuilt or resealed, valley proximity |
| Tuckpointing and mortar joint repair | $300 – $1,200 | Number of joints, height of work, whether it’s isolated or a full course |
| HeatShield flue resurfacing | $900 – $2,200 | Flue diameter and length, number of coats, condition of the existing liner |
| Partial masonry rebuild | $1,400 – $4,000 | Height of rebuild, brick matching, whether the flue tiles are also replaced |
| Full flue reline (DuraFlex system) | $1,800 – $4,500 | Liner length and diameter, appliance type, oil-to-gas conversions and oversized flues cost more |
| Crown, cap, flashing and tuckpointing as one job | $900 – $2,500 | How many systems get addressed at once, rather than one at a time |
What pushes a job toward the top of a range: a flue that’s too tall for a short liner, an appliance conversion that changes what the liner has to handle, a chimney that’s pulling away from the roofline, and water that’s been getting in behind the flashing for more than a season. What keeps it low: catching a cap or a crown crack before water reaches the mortar, and having the whole system looked at so one visit covers the diagnosis.
We’re a Tundra Chimney Sweep team, and our approach to pricing is to name the failure and the fix, then quote both. If the flue qualifies for HeatShield resurfacing, we tell you that instead of quoting a full reline. That difference alone can save a homeowner well over a thousand dollars, and it’s the reason we keep HeatShield certified application capability in our toolset.
What Affects Chimney Repair Pricing in St. Paul
The same repair can price differently from one St. Paul block to the next. These are the factors that move the number most here.
- Housing stock and chimney age. Much of St. Paul’s housing is older masonry construction, and older flues have often been relined once already. A second reline over an old, unlined chimney is a more technical job than a first-time one, so it prices higher. Brick that crumbles when probed means a rebuild, not a patch.
- Freeze-thaw exposure. The city’s long cold season followed by a wet thaw is hard on mortar, crowns and flashing. Chimneys on the windward, shaded side of a house take the worst of it, and those often need more joint repair than a sun-exposed chimney of the same age.
- Appliance type. A wood-burning fireplace, a gas insert and an oil furnace all ask different things of a flue. An oil-to-gas conversion often means the existing flue is oversized for the new appliance, and that’s a DuraFlex liner job, not a simple repair.
- Flue size and configuration. An oversized masonry flue, an offset or a flue with multiple connections costs more to address correctly, because the liner has to be specified to fit the actual path, not the nominal dimensions.
- Roof access and height. A steep pitch, a high ridge, or a chimney set against a dormer changes how much time a proper repair takes. This is a real cost factor in St. Paul’s many two-story and steep-roofed homes.
- Whether it’s caught early or late. A crown crack patched in the first year is cheap. The same crack left through two winters means water behind the flashing, damaged mortar and possibly a rebuild. Timing is the biggest lever a homeowner controls.
Roofs and chimneys also interact with the city itself. In neighborhoods like Summit Hill and Macalester-Groveland, where mature trees keep roofs shaded and damp, flashing and mortar issues show up sooner. That’s not a sales pitch – it’s the reason a cap and flashing inspection is worth doing before anything else on the list.
How to Save on Chimney Repair
Saving money on a chimney repair in St. Paul comes down to catching problems earlier and addressing the system as a whole rather than one part at a time. Here’s what actually helps.
- Fix the water intrusion first. A properly fitted Famco or Gelco cap and sound flashing cost far less than the masonry they protect. Water is the single most expensive thing a chimney deals with in this climate, and stopping it early is the cheapest repair you’ll ever make.
- Ask about resurfacing before relining. If your flue is deteriorated but still structurally sound, HeatShield resurfacing can restore it without full demolition or a complete liner replacement. It’s worth asking specifically, because not every company can apply it.
- Bundle the work into one visit. A crown repair, a cap and a tuckpointing job done together usually cost less than the same three jobs quoted separately, because you’re paying for one setup and one trip up the roof.
- Get the inspection in writing and keep it. Our inspection service documents system condition in writing, and that document is genuinely useful for insurance claims and real estate transactions. It also gives you a clear picture of what needs doing now versus what can wait.
- Get a free estimate and compare scope, not just price. The lowest bid is often low because it’s patching instead of fixing. Call (866) 942-6061 for a free estimate and ask every quote the same questions about materials and approach.
Because we handle sweeping, repair and inspection under one roof, you don’t have to bring in a separate inspector after a repair is done. The same team that diagnoses the flue does the work and documents it. That coordination saves both money and the aggravation of chasing paperwork between companies.
Why the Materials Behind the Estimate Matter
A repair is only as good as the components in it, and in a St. Paul winter the difference between a professional-grade component and a cheap substitute shows up fast. We specify DuraFlex liners, HeatShield resurfacing systems, Gelco and Famco caps and flashing, Olympia Chimney components and Copperfield products because each one is built for sustained heating-season load. We use Famco and Gelco because a cap that’s properly fitted to the flue stops water and animals at the top, where most damage starts. We use DuraFlex because flexible liner systems are what make oil-to-gas conversions and oversized masonry flue upgrades reliable.
The reason this matters for pricing is simple: a cheap cap that doesn’t seal correctly means you’re paying for the same water damage repair again next season. The whole system has to hold up from the first cold snap to the last thaw, and that’s the standard we hold every repair to.
When a Repair Becomes a Replacement
A homeowner’s real question is often whether to repair at all or put the money toward a rebuild. In St. Paul, a chimney that’s lost structural integrity through the middle of its height, or whose flue is cracked beyond what resurfacing can fix, is usually a rebuild candidate. A chimney with a damaged flue but a sound exterior is usually a reline candidate, and a chimney with isolated cracking and a solid structure is usually a repair.
Our technicians have up to 11 years of experience diagnosing exactly this, and the honest answer is that plenty of St. Paul chimneys get relined when they could have been resurfaced, and plenty get patched when they needed a rebuild. Getting an in-person look before committing is the only reliable way to know which path is right for your flue. We treat the sweep, the repair and the inspection as parts of one system, so the recommendation reflects the whole thing.
The Cost of Waiting Through a St. Paul Winter
The climate here doesn’t forgive deferred chimney work. Water gets into a hairline crown crack, freezes overnight, expands, and widens the crack – which lets in more water the next time it rains. Repeated across a long cold season and a spring thaw, a $250 crown repair quietly turns into a $2,000 rebuild. That’s not a scare tactic; it’s how masonry fails in this part of Minnesota.
The flip side is that catching things early genuinely pays. A cap and flashing inspection on a sound chimney is a modest expense, and it’s the best insurance against the kind of water damage that drives the big line items on the table above. If you haven’t had the system looked at since the last heating season, a sweep and inspection is the cheapest way to find out where you stand.
What’s Included in a Free Estimate
When you call for a free estimate, a technician comes out, inspects the flue, cap, crown, flashing and masonry, and gives you a written quote that names the failure and the fix. There’s no dispatch fee and no charge for the estimate itself; the price you’re quoted is set per job by that written estimate. If part of the work can wait, we say so. If the flue qualifies for HeatShield resurfacing instead of a reline, we say that too.
You’ll also get a clear picture of how the repair should hold up through the heating season, which matters more in St. Paul than in a mild climate. The goal is a system specified for real cold-weather performance, not a patch that gets you to spring and fails again.
Frequently Asked Questions
How much does chimney repair cost in St. Paul?
Most single-issue chimney repairs in St. Paul cost between $150 and $1,400, and a full flue reline runs $1,800 to $4,500. The exact figure depends on what’s failed, how long it’s been failing, and how the flue is configured. Call (866) 942-6061 for a free estimate – the written quote sets the final price.
Is it cheaper to repair or replace a chimney?
Repair is cheaper in most cases – a $200 to $700 crown repair or a $900 to $2,200 HeatShield resurfacing costs far less than a rebuild, which runs $1,400 to $4,000 or more. Replacement becomes the cheaper long-term choice only when structural damage is widespread. An inspection tells you which situation you’re in. Call (866) 942-6061 for a free assessment.
Can you come today?
Often, yes. We answer 24/7 and dispatch from 7am to 7pm Sunday through Friday. Call (866) 942-6061 and we’ll find the next opening for a free estimate and a proper look at the flue.
How much does a chimney cap or flashing repair cost?
A cap replacement typically runs $150 to $500, and flashing repair $250 to $850. Both are among the least expensive repairs we do and the best protection against the far larger water-damage jobs they prevent. Call (866) 942-6061 for a free estimate.
Do I need a full reline or just a repair?
A full reline typically runs $1,800 to $4,500, while a HeatShield resurfacing runs $900 to $2,200 and is often enough when the flue is sound but the interior surface is deteriorated. The only way to know which applies to you is an inspection. Call (866) 942-6061 for a free estimate and a clear recommendation.
Does chimney repair cost more in winter?
No. The price is set per job by the written estimate regardless of when the work happens. Call (866) 942-6061. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Getting a Real Number for Your Chimney
Chimney repair in St. Paul is not an item where a single price fits every house. The ranges in this guide are here so you walk into the conversation knowing where the numbers come from and what moves them – not so anyone can quote your roof over the phone. The next step is a real look at your flue, crown, cap and flashing, and a written estimate that names the failure and the specific fix.
We work with professional-grade brands like DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco and Copperfield because in this climate a repair has to hold up under the full heating season, not just the mild weeks. Our technicians have up to 11 years of experience, and we’d rather resurface your flue than sell you a reline you don’t need. For more on the repair work itself, see our chimney repair page.
Call (866) 942-6061 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the St. Paul market as of 2026. Tundra Chimney Sweep offers free estimates – call (866) 942-6061.
Written by the team at Tundra Chimney Sweep.
What Our Customers Say
"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Scott Parker"Showed up when they said they would. That's most of the battle."
- Allen Chen"Good work. The written inspection report took about a week to arrive after I asked for it, which was slower than I expected."
- Doug Miller